Prev: D588 Up: Map Next: D703
D672: Draw a landscape step
The draw shared by every direction, reached from landscape_step_loop, set_right_clip_columns, slope_lose_last_column, use_mirrored_right_clip, slope_step_at_left_edge and flat_step_clip (which jumps into it past the first lines with DE already holding a cap's graphic offset). It turns the variant into a graphic address and loads SP with it. If the step hangs below the play area (piece_y from $B8) it pops the rows below the edge away and starts at the bottom row; if it reaches above the top it shortens the row count (and, for a slope, cuts the piece short, since pieces only climb). Then the JR at the end, whose displacement was set to 0, 2, 5, 8 or 11 (0 by landscape_step_loop, the others by the clipping set-ups), lands on one of the five jumps at step_dispatch: the step's own blitter (IY) or one of the four edge-clipping blitters.
Every blitter is entered with A = row pairs to draw, HL = the screen address less the step's byte advance, SP = the first graphic byte, and ends by jumping to after_step_drawn with HL where the next step will start.
Input
E Variant (0-2)
HL' Screen address of the step, less the byte advance (column_address)
draw_step D672 LD A,E Normal graphic: the offset from this direction's variant row (piece_offsets + 2 * variant).
D673 EXX
D674 LD HL,(piece_offsets)
D677 LD E,A
D678 SLA E
D67A LD D,$00
D67C ADD HL,DE
D67D LD E,(HL)
This entry point is used by the routine at flat_step_clip.
draw_step_0 D67E LD HL,(piece_graphic) SP = the step's graphic. (A cap's offset joins here.)
D681 ADD HL,DE
D682 LD SP,HL
D683 LD A,(half_rows) E = row pairs. Does the step hang below the play area (piece_y from $B8)?
D686 LD E,A
D687 LD A,(piece_y)
D68A CP $B8
D68C JP C,draw_step_3
D68F SUB $B7 It does: lose half the overhang in row pairs, and pop those rows of the graphic away (D POPs a row pair: the byte advance, plus one for a sloped step off a byte boundary).
D691 LD B,A
D692 SRL B
D694 LD A,E
D695 SUB B
D696 LD E,A
D697 LD A,(piece_step_y)
D69A LD D,A
D69B LD A,(piece_rise)
D69E AND A
D69F JR Z,draw_step_1
D6A1 LD A,(IX+$00)
D6A4 AND $07
D6A6 JR Z,draw_step_1
D6A8 INC D
draw_step_1 D6A9 LD A,D
draw_step_2 D6AA POP HL
D6AB DEC A
D6AC JR NZ,draw_step_2
D6AE DJNZ draw_step_1
D6B0 LD H,$57 Start at the play area's bottom row (pixel row $B7) in the step's column.
D6B2 LD A,(column_address)
D6B5 LD L,A
D6B6 LD A,(piece_dcolumn)
D6B9 ADD A,L
D6BA AND $1F
D6BC OR $C0
D6BE LD L,A
D6BF LD A,(piece_dcolumn)
D6C2 NEG
D6C4 ADD A,L
D6C5 LD L,A
D6C6 LD A,($D702) For the mirrored left-clipping blitter a column past 28 belongs to the character row above.
D6C9 CP $0B
D6CB JP NZ,draw_step_6
D6CE LD A,L
D6CF CP $DD
D6D1 JP C,draw_step_6
D6D4 LD A,L
D6D5 SUB $20
D6D7 LD L,A
D6D8 JP draw_step_6
draw_step_3 D6DB LD B,A Not below: does the step reach above the top row ($18)?
D6DC LD A,(piece_rows)
D6DF NEG
D6E1 ADD A,B
D6E2 SUB $18
D6E4 JP NC,draw_step_5
D6E7 CPL It does: shorten it; a slope's piece is cut to at most one more step (C' = 2 unless already 1).
D6E8 SRL A
D6EA NEG
D6EC ADD A,E
D6ED LD E,A
D6EE LD A,(piece_rise)
D6F1 AND A
D6F2 JR Z,draw_step_5
D6F4 EXX
D6F5 LD A,C
D6F6 CP $01
D6F8 JR Z,draw_step_4
D6FA LD C,$02
draw_step_4 D6FC EXX
draw_step_5 D6FD LD HL,(column_address) HL = the screen address kept for this step.
draw_step_6 D700 LD A,E A = row pairs to draw.
draw_step_7 D701 JR draw_step_7 Patched dispatch: displacement 0, 2, 5, 8 or 11 lands on one of the five jumps that follow.
Prev: D588 Up: Map Next: D703